TemGlass All articles
Engineering & Design

Drift, Clearance, and the Fallout Question: Reviewing Tempered Glazing in U.S. Seismic Zones

TemGlass
Drift, Clearance, and the Fallout Question: Reviewing Tempered Glazing in U.S. Seismic Zones

Wind and guard loads push on glass. Earthquakes move it. That difference in loading direction is what makes seismic review of tempered glazing a distinct discipline, and it is why a system that passes a wind pressure calculation can still shed panels during a moderate event.

Nonstructural provisions in ASCE 7 treat glass in glazed curtain walls, storefronts, and interior partitions as components that must accommodate the seismic relative displacement of the structure around them. The glass itself is rarely the weak link in the analysis. The weak link is usually the clearance, the setting detail, or the assumption that a tempered panel behaves like a fixed plate when the building racks.

Seismic Is a Displacement Problem

The controlling quantity is the design story drift — the horizontal movement of one floor relative to the floor above or below, expressed as a percentage of story height. For a glazing system, that drift converts into a relative displacement across the panel's own opening, typically calculated from the displacements at the top and bottom of the glazed assembly rather than from the drift ratio alone.

A useful rough calibration: at a two percent drift ratio over a twelve-foot story, the top of that story moves nearly three inches relative to the bottom. A framed opening in that story must absorb a meaningful fraction of that movement, or the glass must be detailed to follow the frame without being pinched. Both outcomes are design decisions, and neither happens by default.

Getting the Drift Number, and Getting It Early

The drift figure belongs to the structural engineer of record. It arrives as a story drift ratio, sometimes as an envelope across the building height, and it must reach the glazing system designer while the frame profile is still open to change. When the number arrives after the curtain wall is released, the conversation shifts from design to retrofit.

Two follow-on checks matter. First, drifts at a given story often differ between orthogonal directions, and glass with an unequal support condition can fail in either. Second, interior partitions see drift too. Office fronts, conference room enclosures, and corridor glazing that are not part of the lateral system still move with the floors to which they are anchored.

Clearance Is Where Seismic Review Is Won or Lost

Edge clearance is the detail most frequently compromised in the field and most frequently overlooked in the submittal. Glass must not bear on the frame at its edges; it must sit in setting blocks, with clearance at the head, sill, and jambs that allows the frame to move without transferring that movement into the panel edge.

Reviewers should trace clearance through the entire installation, not just the shop drawing detail:

Tempered, Heat-Strengthened, or Laminated

Tempered glass is required in many of these locations for human impact reasons, not seismic ones. When it breaks, it breaks completely and into dice, which is good for hands and less good for retention in the frame.

Laminated glass with a stiff ionoplast interlayer is the more common choice where fallout is a concern — in exit enclosures, above occupied space, and on elevations where glazing sits over walkways. The interlayer holds broken lites in the frame and provides residual capacity after fracture. A laminated assembly of two tempered lites offers both the impact classification and the post-break integrity, at a cost premium and a weight penalty that must be carried through anchorage and framing.

For glazing that does not require tempered safety glass, heat-strengthened laminated assemblies are frequently used in seismic curtain walls because the break pattern is less energetic and the laminated unit stays in place. The product choice should follow from what the project is trying to protect, not from habit.

Anchorage, Frames, and the Untested Assumption

A well-detailed glass panel in a rigidly anchored frame still cracks when the frame does not move as intended. Anchors should be designed under the nonstructural component provisions of ASCE 7 Chapter 13, with slotted connections, oversize holes, or other allowances that accommodate drift and construction tolerance. Slip joints in mullion splices, expansion provisions at floor lines, and seismic separation joints at building interfaces all need review.

One further caution: glass should never be relied upon to brace or stiffen the frame. Where a system's stiffness depends on the panels, drift will eventually supply the proof.

Testing and Mockups

Two test standards are routinely specified. AAMA 501.4 is a static drift test that evaluates a wall system under repeated in-plane racking; AAMA 501.6 is a dynamic test that determines the drift magnitude at which glass leaves the system. A lab report from a comparable system is the strongest evidence a submittal can carry, provided the tested configuration matches the project's glass makeup, frame, and anchorage. Where it does not match, an on-site or laboratory mockup tested to the project's design drift is the defensible alternative.

Buyers should ask for the report and read the drift level at which the test was run. A system certified at one percent drift is not a substitute for one that must accommodate two and a half.

A Review Checklist Before Shop Drawings Lock

  1. Obtain design story drift and the calculated relative displacement at each glazed assembly.
  2. Confirm the frame system's tested drift capacity, or schedule a mockup test.
  3. Verify head, sill, and jamb clearances on every typical and atypical detail.
  4. Confirm setting block material, location, and hardness.
  5. Specify laminated glass with an ionoplast interlayer wherever fallout is unacceptable.
  6. Review anchors and embeds for drift accommodation, not just gravity and wind.
  7. Check that interior partitions and office fronts are included in the seismic review.
  8. Coordinate with fire-rated glazing requirements where the two overlap in stairs and corridors.
  9. Where the project is an essential facility in California, confirm the additional review requirements of the applicable state agency.
  10. Confirm special inspection and testing obligations are assigned before construction begins.

Seismic review that starts at the mockup stage becomes a redesign. Started at the drift calculation, it is a series of small, inexpensive confirmations — which is what it should be, given that the glass is usually the last item to arrive and the first to be blamed.

All Articles

Related Articles

Frit, Furnace, and Final Color: Specifying Printed Glass That Survives Tempering

Frit, Furnace, and Final Color: Specifying Printed Glass That Survives Tempering

The Fire Rating Lives in the Assembly: Why Tempered Glass Cannot Carry a Fire Separation Alone

The Fire Rating Lives in the Assembly: Why Tempered Glass Cannot Carry a Fire Separation Alone

Between the Shaft and the Code: Why Elevator Glazing Answers to a Regulator Most Glass Buyers Never Meet

Between the Shaft and the Code: Why Elevator Glazing Answers to a Regulator Most Glass Buyers Never Meet