TemGlass All articles
Market Analysis

The Five Details That Turn a Clean Quote Into a Costly Change Order

TemGlass
The Five Details That Turn a Clean Quote Into a Costly Change Order

Photo: Internet Archive Book Images, No restrictions, via Wikimedia Commons

The Quote That Doesn't Hold

Every procurement professional in commercial construction has lived this sequence: a tempered glass RFQ goes out, three suppliers respond within the deadline, the numbers look competitive, a vendor is selected — and then the real costs begin to surface. Holes nobody specified. Edge treatment assumed one way by the fabricator and another by the architect. A silkscreen pattern whose placement was never dimensioned.

The problem is rarely dishonest pricing. It's that a glass quotation is a snapshot of assumptions, and when the RFQ is silent on a detail, every supplier fills that silence differently. The lowest number on the spreadsheet is frequently the one built on the most optimistic assumptions — and the gap gets settled in change orders, not in the bid.

Below are the five details that most reliably trigger re-pricing on tempered glass orders in the US market, along with a checklist your team can circulate before the RFQ leaves the building.

1. Hole Patterns, Diameters, and Distance-to-Edge

Drilled or notched tempered glass cannot be reworked after heat treatment — the panel either meets spec or becomes scrap. That finality is why hole details carry so much pricing weight.

When an RFQ says "holes per attached drawing" and the drawing is missing, fabricators quote either without holes or with a generic allowance. Both scenarios unravel at order entry. What procurement should confirm before requesting pricing:

A panel with a single 1/4-inch hole near a corner is a different manufacturing proposition than one with six countersunk fittings along a rail, and the price will reflect that — if the detail exists at quote time.

2. Notches and Cutouts — Tolerances Included

Notched panels for clamps, handrails, and door hardware are common, and so are the disputes that follow them. The recurring failure is tolerance: the drawing shows a notch, but nothing states whether it's held to ±1/16 inch or ±1/8 inch. Tighter tolerances mean more careful layout, more inspection, and higher rejection risk — all of which cost money.

Also confirm corner radii. Sharp internal corners in tempered glass are stress concentrators; most fabricators will require a radius whether you ask for one or not. If the architect's drawing shows a square notch, resolving that conflict before the quote — not after — is the entire point of this exercise.

3. Edge Treatment: Seamed, Grind, Polish, or Bevel

"Standard edge" is not a specification; it's a negotiation waiting to happen. In US practice, the default for tempered panels is usually a seamed or swiped edge — enough to remove sharpness, nothing more. But exposed applications, frameless doors, and retail conditions often call for a flat or pencil-polished edge, which adds handling and machine time per linear foot.

The re-pricing trap is architectural intent: the drawings show a frameless canopy with polished edges, while the RFQ — written from a bill of materials — says nothing about edges at all. State the edge treatment for every edge type, on every panel group, in the RFQ itself.

4. Print, Etch, and Logo Placement

Two markings matter on tempered glass: the permanent certification stamp (required under CPSC 16 CFR 1201 and ANSI Z97.1 for safety glazing) and any decorative ceramic print or etched logo. Both have placement rules, and both get ignored in RFQs.

The certification stamp must appear in a location permitted by the applicable standard — often a corner or within a few inches of an edge. If the design calls for exposed glass with minimal visual clutter, stamp placement becomes a design conversation. Meanwhile, decorative frit patterns and logos require artwork, screens, and setup charges that only appear on the invoice once. Ask during quoting: who supplies the artwork, in what format, and who approves the first article?

5. Annealing and Heat-Soak Requirements

Not every order is straightforward tempered glass. Some applications call for heat-strengthened panels; others — particularly overhead or high-occupancy installations — may warrant heat-soak testing to screen for nickel sulfide inclusions. If the RFQ is silent, suppliers will quote plain tempered glass, and the engineering review later in the process will surface the discrepancy as a cost adder and a schedule hit.

Heat-soak capacity is also uneven across US fabricators. If your project requires it, that requirement can change which suppliers can even bid — another reason to state it up front rather than discover it downstream.

A Pre-Quote Checklist for Procurement Teams

Before an RFQ goes out, circulate this internally and require written answers:

  1. Holes: diameters, locations, edge distances, countersink or straight, reference drawing attached
  2. Notches/cutouts: dimensions, internal corner radii, tolerance class
  3. Edges: treatment per edge type (seamed, grind, flat polish, pencil polish, bevel)
  4. Markings: stamp placement per code, decorative print/etch artwork status and approval path
  5. Thermal spec: fully tempered vs. heat-strengthened, heat-soak requirement if any
  6. Drawings: revision number, dimensioned, and attached to the RFQ itself — not "to follow"

Pricing Is a Specification Problem

The most reliable way to compare tempered glass suppliers is to give them all the same complete information. When the RFQ closes the gaps above, the quotes that come back are comparable, the selected price is the real price, and the change order disappears from the project vocabulary. In a market where glass lead times already carry schedule risk, the cheapest specification is the one that never has to be revised.

All Articles

Related Articles

Guard Loads and Glass Views: What Multifamily Developers Owe Their Balcony Railing Specs

Guard Loads and Glass Views: What Multifamily Developers Owe Their Balcony Railing Specs

Before the Furnace or After: Why Coating Sequences Decide What Your Tempered Glass Order Can Actually Do

Before the Furnace or After: Why Coating Sequences Decide What Your Tempered Glass Order Can Actually Do

Shattered, Shipped, Buried: Following a Failed Tempered Panel to the End of Its Life

Shattered, Shipped, Buried: Following a Failed Tempered Panel to the End of Its Life